Installing Noodoe EV's
W1000 EV CHARGER
HOW TO INSTALL YOUR W1000 CHARGER
|Ensure that you have read the installation guide and the user manual.
|Ensure that the power system of the installation site has been confirmed. The power capacity must be more than 40A. The following is the power system required:
a) 208V/2-phase and neutral grounded, made from 3-phase, 4-wire wye system, or
b) 240V/split-phase neutral grounded, made from 3-phase, 4-wire delta system, or
c) 240V/split-phase and neutral grounded, made from single-phase, 3-wire system.
|Ensure that you know how the charger will connect to the internet.
Noodoe EV chargers require an internet connection to provide EV charging services. You may need a router with a 4G connection if a wired Internet connection is not available.
|Ensure that the installation permit has been received and the installation date and time are confirmed with the project manager/property representative.
|If you’re performing a pedestal installation ensure that the concrete pad construction has been completed (if the charger type is wall-mounted, this step can be skipped).
|Prepare qualified AC power hard wires and RJ45 hard wired internet cable (CAT.6 at least) of adequate length for the installation site.
|Ensure that the related tools have been prepared, including but not limited to:
a) Wire strippers
b) Voltmeter or digital multi-meter, used for measuring AC voltage at the installation site
c) Phillips screwdriver
d) T8 Torx screwdriver
f) Electric drill
g) Adjustable wrench
What's In The Box
|EV Charger with charger connector cable
|Hook with lock
|Mounting accessories for the charger
|Installation guide and user manual
|M4 X 8mm screws (flat)
|M5 X 6mm screws (round) – 6
|M6 X 30mm expansion screws (self tapping screws + expansion pipes)
|L type instruction board
|T8 Torx screwdriver
Follow the instructions in the Quick Start Guide or the more granular User’s Guide to complete the installation of the EV charging stations.
Set up internet connection
NOTE: Noodoe EV charging stations require internet connectivity to complete charger activation and to provide charging services.
The charging station comes with a standard RJ45 connector. You can choose to connect the charger to a wired internet connection at the site or to a switch that is connected to a 4G router.
If An Internet Connection Exists
Connecting your charger to the internet is easy if you already have a wired internet connection.
If An Internet Connection Is Not Available
You have to establish a connection via a 4G router. If you're installing multiple chargers at a given site you may use an internet switch to extend Internet connectivity for multiple chargers:
IMPORTANT: A high-quality commercial-grade 4G router is required for stable operation of the charging stations.
A consumer router will freeze after a few months and require a reset. Commercial-grade routers are designed for years of continuous operation under harsh conditions. Additionally, they can auto-reboot should the routers stop working. This ensures dependable, automated service. Please contact your Noodoe EV representative or distributor if you require help with obtaining a commercial-quality Noodoe-certified 4G router.
Additional Internet Considerations:
- Confirm that the end to end ping response is less than 100ms.
- Confirm that the signal strength at the installation point indicates full strength or close to it.Make sure that you monthly data quota is at least 2GB.
- Place the 4G router in a location where it does not experience any interference or where signal is blocked.
- Avoid intermingling power lines with network lines to eliminate chance of interference.
- Make sure to use cables that are Cat5e or above with a maximum length of less than 100m or a switch should be deployed.
- Dedicated AP (access points are required). Do not exceed more than 2 APs.
- The following ports must be opened by firewall in order for the charging station to communicate: 22, 8998, 16000.
After all the electrical work has been completed and an internet connection has been established, you can power up the charging station. Open up the side cover with a T8 Torx screwdriver and turn the breaker to the ON position.
Continue to Activation
Need help? If you’re still experiencing issues or would like to ask any questions specific to your installation, please fill out the form, and we will respond promptly.